Prices shown are subject to change with out notice.

Valve Work
VW1 Install hardened valve seat - $75.00
VW2 Serdi Vaccum test heads - $20.00
VW3 3 Angle cut on valve seat (1) - $30.00
VW4 5 Angle cut on valve seat (1) - $50.00
VW5 Grind valve (1) - $7.00
VW6 Install and size guides (4) - $65.00
VW7 Set valve spring pack to cam - $75.00
VW8 Machine spring collar floors - $50.00
VW9 Blasting & cleaning (2 heads) - $50.00

Head Work
HW1 True head gasket surface (1) - $45.00
HW2 Deck head gasket surface (.050") - $50.00
HW3 Repair blown head gasket surface - $175.00
HW4 Repair spark plug (2) - $50.00
HW5 Replace panhead exhaust flange (1) - $100.00
HW6 Repaire shovel exhaust stud hole - $40.00-$100.00*
*DEPENDING ON WELDING REQUIREMENTS
HW7 Repaire O-ring intake flange (2) - $150.00
HW8 Convert plumber int. to O-ring - $175.00
HW9 Porting and flow test - $150.00/hour
HW10 Machine heads for 3 5/8" (PR) - $150.00
HW12 CC 883 heads for 1200 (PR) - $275.00
HW13 Install compression release Evo (2) - $200.00
HW14 Install compression release TC (2) - $100.00

Cylinder Work
CW1 Bore cylinder up to (.020) over each - $50.00
CW2 Bore cylinder (.030) thru (.060) each - $75.00
CW3 Bore cylinder W/ torque plates (1) - $75.00
CW5 Bore 883 to 1200 (PR) - $225.00
CW6 Hone cylinder/break glaze only each - $20.00
CW7 Bore 88 TC to Big Bore - $225.00
CW8 Cast iron heads/cylinders/painted - $60.00

Dual Plug
DP1 Dual plug shovelheads (PR) - $200.00
DP2 Dual plug evolution heads (PR) - $200.00
DP3 Dual plug cast xl heads (PR) - $250.00
DP4 Dual plug "STD" panheads (PR) - $250.00

Misc
M1 Flow testing by the hour - $150.00/hour
M2 Head porting by the hour - $200.00/hour
M3 General machining by the hour - $125.00/hour
M4 Glass beads blasting by the hour - $75.00/hour
M5 Cleaning by the hour - $75.00/hour
M6 Install timesert - $20.00
M7 Install keensert - $25.00
M8 Install timesert sparkplug hole (2) - $50.00
M9 Install & hone 4th gear bushing - $45.00
M10 Remove/replace tappet rollers xl & shovel (4) - $40.00

Transmission Rebuilt
TR1 4 speed big twin - $350.00
TR2 Ratchet lid rebulit - $100.00
TR3 5 speed big twin - $300.00
TR4 4 speed sportster - $480.00
TR5 5 speed sportster - $450.00

Case Repair
CR1 Repair breather hole - $175.00
CR2 Bore breather hole for oversize - $90.00
CR3 Bore pan case for cam brearing - $125.00
CR4 Relieve case for high lift cam - $30.00
CR5 Weld and Repair timing hole - $150.00
CR6 Weld alternator O-ring flange - $150.00
CR7 Deck cylinder base on cases (PR) - $150.00
CR8 Machine cases for 3 5/8" cylinder - $150.00
CR9 Machine cases for 3 13/16" cylinder - $175.00
CR10 Machine TC cases for 4 1/8" cylinder - $225.00
Cr11 Machine cases for stroker flywheels - $125.00
CR12 Machine & install scraper plates - $125.00
CR13 Machine & install steel ring for alternators - $150.00

Rods & Flywheels
RF1 Electronic spin balance flywheels - $150.00
RF2 Repair flywheel thrust washer hole (2) - $100.00
RF3 Hone rods to fit crankpin - $75.00
RF4 Remove & replace rod races - $75.00
RF5 Hone piston pin bushings - $30.00
RF6 Remove & replace piston pin bushings - $30.00
RF7 True flywheels & weldnuts - $100.00
(Does not include heavy metal)

Complete Engine Rebuilds (Stock Engines) Price
CE1 All Big Twins - $1325.00
CE2 All sportsters (incl.clutch & trans.) - $1600.00

Short Block Rebulid
SB1 All Big Twins (without cams & oil pump) - $450.00
SB2 All sportsters (without cams & oil pump) - $450.00
SB3 Big Twins (with cams & oil pump) - $550.00
SB4 XL-77 and later (with cams & oil pump) - $585.00
SB5 Early XL (with cams & oil pump) - $625.00
*For electronic balancing add $150.00

NOTE: These prices are labor only and they do not include the installation & rebulid of carburetors, starters, generators, alternators, or magnetos.
NOTE: These prices include bead blasting and cleaning - complete rebuilds excluded.